HomeAbout UsProductsEnquiryContact Us  
 
 
 
 
 

Microprocessor Kit

8-Bit Microprocessor Training Kit

(ZES-8502-1)

  • Based on 8085 CPU at 6.144MHz Crystal
  • Total on board memory expansion upto 64KB
  • 4K bytes of EPROM loaded with monitor.
  • 2k byte of RAM with provision for further expansion 6116/6264.
  • Six seven segment Hexadecimal display
  • 24 I/0 lines with provision for expansion upto 48 I/O lines.
  • 16 bit programmable time/counter using 8253
  • On board RS 232C interface for CRT using SID/SOD lines
  • 28 Computer graded keys 16 for Hexadecimal keys and 10 for programming editing, debugging, execution etc.
  • PC UP/DOWN loading facility.
  • PTH, PCB with green marking
  • Housed in an attracted wooden cabinet
  • Built in Power Supply.
 

8031 Micrcontroller Training Kit

(ZES-31/51)

  • Based on 8031/8051/8751 operating at 10/12MHz.
  • Onboard 8k RAM.
  • Battery backup for RAM area.
  • 8/16K bytes of EPROM with powerful monitor program.
  • Total memory expandable upto 128k Bytes using four 28 pin sockets.
  • 48 I/O lines using 2 nos. of 8255.
  • Two external interrupts INTO & INT1.
  • 28 keys Hexadecimal keyboard and six Seven Segment displays.
  • RS-232C interface using 8251
  • Auxiliary RS-232C using serial pins of 80C31.
  • All data address and control signals (TTL compatible) available at FRC connector.
  • Powerful software commands like INSERT, DELETE, BLOCK MOVE, SET/CLEAR BREAK POINT, SINGLE STEP, EXAMINE THROUGH REGISTER, EXECUTE, EXAMINE, MODIFY, PROGRAM/DATA/INTERNAL MEMORY etc.
  • Uploading/Downloading facility from PC in Intel Hex format.
  • Inbuilt power supply
  • User's Manual, Cables & Connectors.
 

8051 Microcontroller Training Kit With LCD Display

(ZES-31/51 LCD)

  • Based on 8051/89C52 microcontroller
  • Onboard 32k RAM.
  • Battery backup for RAM area
  • 64 K bytes of EPROM with powerful monitor program
  • 48 I/O lines using 2 Nos. of 8255.
  • 3 Channel programmable timer/counter using 8253.
  • Two external interrupts INTO & INT1 from CPU
  • IBM PC compatible keyboard for entering the program, editing and executing the programs.
  • 20 x 2 LCD (Liquid Crystal Display) is provided for display.
  • RS-232C interface using 8251.
  • One serial USART interface provided by 89C51/89C52
  • All data address and control signals (TTL compatible) available at FRC connector.
  • Powerful software commands like INSERT, DELETE, BLOCK MOVE, SET/CLEAR BREAK POINT, SINGLE STEP, EXAMINE
    REGISTER, EXECUTE, EXAMINE/MODIFY MEMORY etc.
  • Inbuilt power supply.
    Detailed User's Manual with sample programs
 

INTERFACING MODULES CAN BE CONNECTED WITH ANY MICROPROCESSOR TRAINING CUM DEVELOPMENT KIT

(ZES-6804)

(a) ADC Analog to Digital Converter with temp scanner interface
(b) ADS Analog to Digital Converter using ADC 0809
(c ) DAC 12 bit A/D & D/A converter using MAX 162
(d) DAC Dual Channel digital to analog converter interface.
(e) LNS Ladder Network Simulator
(f) ICT I.C. Tester
(g) ES Elevator Simulator
(h) KY Keyboard Interface
(i) DI Display Interface
(j) LCD 16x1 LCD Display Interface.
(k) SMC Stepper Motor Controller Interface
(l) Stepper Motor (Torque 10Kg/Cm)
(m) Stepper Motor (Torque 6Kg/Cm)
(n) Stepper Motor (Torque 3Kg/Cm)
(o) Drive for Stepper Motor
(p) Power Supply for Stepper Motor (12V/5Amp)
(q) 26 Pin flat Core Cable to connect the modules & kits.
 
HOME | ABOUT US | PRODUCTS | ENQUIRY | CONTACT US
© 2010 Zodiac Electronic & Scientific Corporation. All rights reserved.